BHEL Mechanical Engineering Trainee Question Paper
BHEL Mechanical Trainee Previous Year Paper
Below you can find BHEL Mechanical Trainee Placement Papers with free download pdf. The following sections contain BHEL Civil Trainee Executives Mechanical Electronics Electrical Engineering Previous Years Mechanical Trainee Papers with solution. To Prepare BHEL Exam the best way is to go through Last Year BHEL Question Papers, Previous year Past Years BHEL Question Papers with Solutions. Here you can get Old BHEL Mechanical Trainee question papers with solution. These BHEL Last Years Papers help you crack BHEL Exam and give answers to the questions like How to Crack BHEL Exam, What is the Eligibility Criterion of BHEL Exam, BHEL Exam Syllabus. BHEL Exam contains mainly Aptitude Technical Reasoning English Questions Papers.
In Mechanical stream there were a total of 240 questions. 120- Technical questions in Mechanical Engineering 120- General Apptitude questions. (Quantitative Aptitude, Reasoning Ability, Logical thinking, English usage)
The questions were mainly asked in Thermodynamics Engineering Mechanics Theory of machines Production tech If you have strong fundas, u can really do well in this session...
Following are the questions asked: (I will try to give you as many questions as i remember) [One Mark for correct answer, 1/5th for wrong answer. Five choices were given]
1)Unit of Entropy (J/kg K or kJ/kg K)
2)A mass of 100kg is falling from a height of 1 m and penetrates the sand into for 1 m. What is the resistance force given by sand.
3)Ratio of specific heats of air. (1.41)
4)A body weighs 3 kg in air. If it is submerged in a liquid, it weighs 2.5 kg. What is the specific gravity of the liquid.
5)Two cars travell in same direction at 40 km/hr at a regular distance. A car comes in a opposite direction in 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between them?
6)A simple problem involing in hoops stress. For sphere: M= [3/2]*p*V*[density of pressure vessel material/Maximum working stress it can tolerate] For Thin walled pressure walls: Hoops stress or stress in the radial direction =p*r/2t
7)A problem in force calculation in a body moving in a inclined surface.
8)Composition of bronze. (Copper+zinc)
9)Compostion of stainless steel.(iron+chromium+nickel+carbon)
10)CI is manifactured in which process. (cupola process) 11)What percentage of carbon is preset in pig iron. (4.5 to 6%)
12)Water is available at 10m height. What is the pressure available? (pressure=density*g*height; p=1000*9.81*10; p=98100N/m2) Ch
13)What will happen if the speed of the centrifugal pump doubles.
14)The unit eV is widely used in ? (Nuclear and atomic physics)
15)What will happen to the resistance, when the diameter of the conductor is doubled?
16)The power comsumed by a electrical device is 1000W at 250V, What is the resistance in the device? (Power= Voltage*current; Current=Power/Voltage, Current,I=1000/250=4 amps. V=IR, Therefore R=250/4=62.5 ohms)
17)Why DC current is not used in transformer.
18)On what principle the sonar/ radar works?
19)Bending moment diagram for the UDL is in what shape?
20)Function of the distributor in petrol vehicles? (Spark timing) 21)Which is not present in CI engines? (carburrettor)
22)What will happen if one cylinder recieves more amount of fuel spray from injectors than other injectors?
23)Purpose of draft tube in hydraulic turbines? (The purpose of a draft tube is toconvert some of the kinetic energy of the flow from the runner (the rotating part of the turbine) intopressure energy and thereby increase the efficiency ofthe hydro power turbine.)
24)What is the effect or reheater in the gas turbine? (The advantage of reheater is significantly increased thrust; the disadvantage is it has very high fuel consumption and inefficiency) )Problems involving with fricition coefficient.
26)Factor of safety = Yeild stress/Working stress. 27)Which is the example of non parallel power transmission (Universal coupling) 28)For perpendicular shafts worm gear is used.
29)A planet gear with 25 teeth is meshed with a sun gear of 100 teeth. Both are connected using a arm. How many rotations are needed for planet gear to complete one rotation around the sun gear?
30)What is equivalent spring constant for spring in parallel?
31) Some questions was asked related to boundry layer and vortex flow.
32) 5 questions were asked in PERT, Process planning, Product planning, Break even analysis.
33)How are tungsten and sintered composite materials are machined? (Electro Discharge Machining, EDM)
For HOT Govt. Jobs Submit your resume!!
Sarkari Naukri, Indian Government Jobs, PSU Jobs, Bank Jobs